Jan
23
Tue
Arc Flash Safety Training (NFPA70E/OSHA 1910) @ Werner Electric - Pewaukee Register
Jan 23 @ 8:00 am – 12:00 pm
Arc Flash Safety Training (NFPA70E/OSHA 1910) @ Werner Electric - Pewaukee | Waukesha | Wisconsin | United States

Learn what causes arc flash, reasons for performing an arc flash analysis, NFPA70E and OSHA regulations and standards, the steps and skills necessary to recognize electrical safety hazards, and information required for accurately performing an arc flash analysis.  Terms such as limited and restricted approach boundary, as well as arc flash protection boundary, arc blast, incident energy and arcing fault current will be introduced. Various methods are used (manual and computer techniques) to calculate the ARC Flash hazards with heavy emphasis on hands-on examples.

Jan
25
Thu
Arc Flash Safety Training (NFPA70E/OSHA 1910) @ Werner Electric - Iron Mountain Register
Jan 25 @ 9:00 am – 1:00 pm
Arc Flash Safety Training (NFPA70E/OSHA 1910) @ Werner Electric - Iron Mountain | Waukesha | Wisconsin | United States

Learn what causes arc flash, reasons for performing an arc flash analysis, NFPA70E and OSHA regulations and standards, the steps and skills necessary to recognize electrical safety hazards, and information required for accurately performing an arc flash analysis.  Terms such as limited and restricted approach boundary, as well as arc flash protection boundary, arc blast, incident energy and arcing fault current will be introduced. Various methods are used (manual and computer techniques) to calculate the ARC Flash hazards with heavy emphasis on hands-on examples.

Jan
29
Mon
PLC Troubleshooting & Maintenance – 14 CE Hours (CLASS FULL) @ Werner Electric - Appleton Register
Jan 29 @ 8:30 am – Jan 30 @ 4:30 pm
PLC Troubleshooting & Maintenance - 14 CE Hours (CLASS FULL) @ Werner Electric - Appleton | Appleton | Wisconsin | United States

This class is designed for those with little to no PLC experience. The instructor teaches basics in connecting to and diagnosing MicroLogix, SLC, CompactLogix, and ControlLogix controllers. Focus will be placed on finding module and processor faults, as well as the resources needed to understand such errors.
CE Hours: 14

Jan
30
Tue
Arc Flash Safety Training (NFPA70E/OSHA 1910) @ Werner Electric - Appleton Register
Jan 30 @ 8:00 am – 12:00 pm
Arc Flash Safety Training (NFPA70E/OSHA 1910) @ Werner Electric - Appleton | Appleton | Wisconsin | United States

Learn what causes arc flash, reasons for performing an arc flash analysis, NFPA70E and OSHA regulations and standards, the steps and skills necessary to recognize electrical safety hazards, and information required for accurately performing an arc flash analysis.  Terms such as limited and restricted approach boundary, as well as arc flash protection boundary, arc blast, incident energy and arcing fault current will be introduced. Various methods are used (manual and computer techniques) to calculate the ARC Flash hazards with heavy emphasis on hands-on examples.

Jan
31
Wed
Logix 5000 Introduction @ Werner Electric - Appleton Register
Jan 31 @ 8:30 am – 12:30 pm
Logix 5000 Introduction @ Werner Electric - Appleton | Wausau | Wisconsin | United States

The Logix 5000 Intro class is geared towards electricians, operators, and maintenance personnel who need a quick overview or brief refresher on the basic components of the ControlLogix and CompactLogix platforms. The class includes RSLinx configuration, controller online activation, programming bit logic, and performing online edits. The class covers the entire Logix platform including both hardware and programming software. No previous Logix experience is required.

Feb
1
Thu
PowerFlex 525 Getting Started – 7 CE Hours @ Werner Electric - Wausau Register
Feb 1 @ 8:30 am – 4:30 pm
PowerFlex 525 Getting Started - 7 CE Hours @ Werner Electric - Wausau | Wausau | Wisconsin | United States

This one-day class is for individuals responsible for starting up, configuring, maintaining, and troubleshooting PowerFlex 520 drives. The class will introduce concepts and techniques that assist in successfully maintaining and troubleshooting a PowerFlex 520 drive. Instruction includes recognizing PowerFlex 520 hardware, properly wiring the drive, and diagnosing specific faults. Exercises that offer hands-on time with a PowerFlex 520 drive are included.
CE Hours: 7

Feb
2
Fri
PowerFlex 750 Getting Started – 7 CE Hours @ Werner Electric - Wausau Register
Feb 2 @ 8:30 am – 4:30 pm
PowerFlex 750 Getting Started - 7 CE Hours @ Werner Electric - Wausau | Wausau | Wisconsin | United States

This one-day class is intended for individuals responsible for starting up, configuring, maintaining, and troubleshooting PowerFlex 750-Series drives. The class introduces concepts and techniques for successfully maintaining and troubleshooting a PowerFlex 753, or PowerFlex 755 drive. Learn to recognize PowerFlex 750-Series hardware, correctly wire the drive, and diagnose specific faults. Included in this class are exercises for hands-on time with a PowerFlex 750-Series drive.
CE Hours: 7

Feb
5
Mon
Studio 5000 Logix Designer Level 4: Kinetix 6500 (CIP) Programming – Provided by Rockwell Automation (CCN144) @ Werner Electric - Fond Du Lac Register
Feb 5 @ 8:00 am – Feb 8 @ 4:00 pm
Studio 5000 Logix Designer Level 4: Kinetix 6500 (CIP) Programming - Provided by Rockwell Automation (CCN144) @ Werner Electric - Fond Du Lac | Madison | Wisconsin | United States

To register for this training, please contact our GSS Team at gssteam@wernerelectric.com

 

Course Purpose

After completing this course, you should be able to configure, test, tune, and program CIP motion axes in the Studio 5000 Logix Designer® programming environment.

Building upon the skills gained in the Studio 5000 Logix Designer Level 3: Project Development (CCP143) course, you will learn how to apply the Logix5000™ architecture to a multi-axis CIP motion control system. You will also practice efficient programming skills necessary for translating a machine specification document into a reliable ladder logic code.

Because all Logix5000 products share common features and a common operating system, you will be able to apply the configuring and programming motion control skills you learn in this course to any of the Logix5000 controllers that are capable of motion control. See the full agenda here!

 

Who Should Attend

Individuals who need to configure and program Logix5000 motion control systems should attend this course. In addition, only students who are already familiar with Logix5000 systems and general motion control should attend this course.

 

Prerequisites

To successfully complete this course, the following prerequisites are required:

  • Completion of the Motion Control Fundamentals course (Course No. CCN130) or equivalent knowledge of Kinetix® 6500 drives, feedback devices, and servo motion systems
  • Completion of the Studio 5000 Logix Designer Level3: Project Development course (Course No. CCP143) or equivalent experience

 

CEUs Awarded

2.8

 

Logix 5000 Foundations – 14 CE Hours @ Werner Electric - Appleton Register
Feb 5 @ 8:30 am – Feb 6 @ 4:30 pm
Logix 5000 Foundations - 14 CE Hours @ Werner Electric - Appleton | Appleton | Wisconsin | United States

This two day class reviews everything from the Logix 5000 Intro class and includes advanced Logix topics such as timers, counters, one-shots, and more. In addition, tools such as BOOTP and ControlFlash will be covered. This class will provide a deeper understanding of the Logix platform and Studio 5000 programming software and help those operating or maintaining those machines achieve a deeper understanding. No previous Logix experience is required.
CE Hours: 14

Feb
7
Wed
Logix 5000 Advanced – 14 CE Hours @ Werner Electric - Appleton Register
Feb 7 @ 8:30 am – Feb 8 @ 4:30 pm
Logix 5000 Advanced - 14 CE Hours @ Werner Electric - Appleton | Appleton | Wisconsin | United States

The Logix 5000 Advanced class sequentially follows the Logix 5000 Foundations class. It focuses on the premier integration of Rockwell devices such as PowerFlex drives, PanelView terminals, Stratix Ethernet/IP switches, Kinetix motion drives, and more. The class will utilize individual lab stations which will each focus on one of these components. The class will provide attendees with a brief overview of how to interface each of these components with Studio 5000. The class will cover the I/O configuration, AOP’s and Logic associated with the hardware. We will also incorporate some of the advanced features and instructions of Studio 5000. The Logix 5000 Foundations class or equivalent Logix experience is required.
CE Hours: 14